Page tree

Versions Compared


  • This line was added.
  • This line was removed.
  • Formatting was changed.

The SZG-ADC-LTC2264 is a 2-channel, 12-bit, 40 MSPS ADC based on the Analog Devices LTC2264-12 ADC. The converter module is perfect for high-performance communications applications and general high-speed data acquisition.

The module is configured to accept a conversion clock from the FPGA on the carrier or (with user-applied resistor changes) a single-ended clock delivered by an on-board SMA connector.


SYZYGY Information

Compatibility Table

Compatibility ParameterSpecification
Port typeSYZYGY Standard
5V supply requiredNo
Nominal 5V supply current0mA
Nominal 3.3V supply current500mA
VIO supply voltage1.2V to 3.3V
Nominal VIO supply current< 10mA
Total number of I/O15
Number of differential I/O pairs5

DNA Data

This data is stored in the SYZYGY DNA microcontroller on the SZG-ADC-LTC226X peripheral.

DNA ParameterData
Max 5V Load0 mA
Max 3.3V Load500 mA
Max VIO Load10 mA
VIO Min1.2V
VIO Max3.3V


SYZYGY (J1)ConnectionNote
5 (D0P)OUT1A+ 
7 (D0N)OUT1A- 
6 (D1P)FR+ 
8 (D1N)FR- 
9 (D2P)OUT1B+ 
11 (D2N)OUT1B- 
10 (D3P)OUT2A+ 
12 (D3N)OUT2A- 
13 (S8)SDO 
14 (D5P)OUT2B+ 
16 (D5N)OUT2B- 
15 (S10)CS_B 
17 (S12)SCLK 
19 (S14)SDI 
33 (P2C_CLKp)DCO+ 
35 (P2C_CLKn)DCO- 
34 (C2P_CLKp)ENC+ 
36 (C2P_CLKn)ENC- 


The design of the SZG-ADC-LT226X has been heavily influenced by the evaluation board designed and produced by Linear Technology (Analog Devices).

Linear Technology (Analog Devices) LTC2262

From the LTC226X datasheet:

The LTC®2265-12/LTC2264-12/LTC2263-12 are 2-channel, simultaneous sampling 12-bit A/D converters designed for digitizing high frequency, wide dynamic range signals. They are perfect for demanding communications applications with AC performance that includes 71dB SNR and 90dB spurious free dynamic range (SFDR). Ultralow jitter of 0.15psRMS allows undersampling of IF frequencies with excellent noise performance.

DC specs include ±0.3LSB INL (typ), ±0.1LSB DNL (typ) and no missing codes over temperature. The transition noise is a low 0.3LSBRMS.

The digital outputs are serial LVDS to minimize the number of data lines. Each channel outputs two bits at a time (2-lane mode) or one bit at a time (1-lane mode). The LVDS drivers have optional internal termination and adjustable output levels to ensure clean signal integrity.

The ENC+ and ENC– inputs may be driven differentially or single-ended with a sine wave, PECL, LVDS, TTL, or CMOS inputs. An internal clock duty cycle stabilizer allows high performance at full speed for a wide range of clock duty cycles.

Analog Inputs

The applicable input frequency range of the SZG-ADC-LTC226X is approximately 5 MHz to 140 MHz. For optimal distortion and noise performance, or for input frequencies above 140 MHz, the RC networks on the analog inputs may need to be optimized. For optimal SNR performance, external filters may be required. Refer to the documentation below.

Maximum analog input voltage: 2 Vpp
The input range may be adjusted using the SENSE pin on the LTC226x. Refer to the documentation below.

Input impedance: 50 Ω

Encode Clock Input

By default, the SZG-ADC is configured to accept a differential clock over the C2P_CLK connection from the carrier. To apply an external single-ended clock over the SMA connector J4, remove resistors R18 and R28, and place resistors R20 and R27.

The encode clock inputs may be driven at any level up to 3.6 V. When driving the inputs using a differential signal, the negative input (ENC-) must stay at least 200 mV above circuit ground.

Additional Documentation

Linear Technology LTC2264-12 data sheet

Linear Technology LTC2264-12 evaluation kit DC1532A-K

Linear Technology LTC2268-14 data sheet

Linear Technology LTC2268-14 evaluation kit DC1532A-A